Explore

Research published in the scientific journals 2014

No.	Published scientific researches for 2014	Download here
1	Gazy F. Al-Sumaily, Forced Convection Heat Transfer From a Bankof Circular Cylinders Embedded in a PorousMedium”, Journal of Heat Transfer · April 2014.
2	Dr. Arkan Al Taie, “Experimental and Numerical Investigation ofConvective Heat Transfer in aCircular Tubewith Internal square ribs”,Journal of Babylon University/Engineering Sciences/ No.(4)/ Vol.(22): 2014.
3	AzherRazzaqHadiWitwit, AzmanYasin, Horizon Gitano, Mohammed Ismael Mahmood, “Best Multiple Non-linear Model Factors for knock Engine (SI) by using ANFIS”, Asian Journal of Applied Sciences (ISSN: 2321 – 0893) Volume 02 – Issue 04, August 2014.
4	Asst. Prof. Dr. Mohsin NooriHamzah, “VISCOELASTIC RESPONSE OF THE THORAX UNDER DYNAMIC LOADING”, Al-Qadisiya Journal For Engineering Sciences, Vol. 7,No. 3,2014.
5	Khalil Ibrahim Abaas, “The Effect of Using a Paraffin Wax-Aluminum Chip Compound As Thermal Storage Materials in a Solar Air Heater”, Issue No. 34/2014.
6	Samir Ali Amin Al-Rubaie, Qasim Abbas Atiah, ZuhairAltaher, “Determination of Optimum Welding Parameters for FSW”, Al-Khwarizmi Engineering Journal, Vol. 11, No. 1, P.P.51-64, 2015.
7	Dr. Shaker Sakran Hassan, Dr. Sadeq Hussein Bakhy, Athraa Ali Jawad, “Effects of Welding Position, Heat Treatments, and Surface Roughness on the Fatigue Behavior of Welded Aluminum Alloys Using Friction Stir Welding”, Eng. & Tech. Journal ,Vol.32, Part (A), No.11, 2014.
8	Wahid Shati Mohammad, Abbas J Jubear, “Numerical Simulation of The Influence of Geometric Parameter on The FlowBehavior in a Solar Chimney Power Plant system”, Journal of Engineering, Number 8 Volume 20 August – 2014.
9	Adel M. Salih and Miqdam T.Chaichan, “The effect of initial pressure and temperature upon thelaminar burning velocity and flamestability forpropane-air mixtures”, September 2014.
10	IhsanA.Baqer, “A Novel Fingertip Design for Slip DetectionUnder Dynamic Load Conditions”, Journal of Mechanisms and Robotics · March 2014.
11	Dr. Wahid S. Mohammad, Assad Oda Jassim, “Experimental and Theoretical Investigation of Propane/Butaneand Propane/Isobutane Mixtures as an Alternative to R134a in aDomestic Refrigerator”, Eng. & Tech. Journal ,Vol.32, Part (A), No.5, 2014.
12	Dr. Hussein M. Al-Khafaji, Prof. Dr. Muhsin J. Jweeg, “Compensating the End-Effector Position of Semi-Flexible Robot Using Smart Structure Technique”, Basrah Journal for Engineering Sciences, vol. 14, no. 2, 2014.
13	Dr. Akeel Abdullah Mohammed, Bashar Ali Mohammed, Dr. Raheem JewiMuhee, “Heat Transfer Enhancement in a Tube Fitted withNozzleTurbulators, Perforated Nozzle-Turbulators withDifferent hole shap”, Eng. &Tech.Journal, Vol. 32,Part (A), No.10, 2014.
14	Ahmed S. Yousif, Gary L. Solbrekken, “Analysis of using ferrofluid as an interface material in a fieldreversible thermal connector”, Journal of Electronic Packaging, Transactions of the ASME · November 2014.
15	Mladen A. Tomić, Predrag M. Živković, Mića V. Vukić, Sadoon K. Ayed, “METODOLOGIJA ZA ODREĐIVANJE KOEFICIJENTA PRELAZATOPLOTE ZA PERFORIRANU PLOČU”, October 2014.
16	Hayder A. Dhahad, Ekhlas M. Alfayyadh ,Mohammed A. Abdulhadi, T. Megaritis, “An Investigation of the Relation Between Combustion Phase and Emissions of ULSD & RME Biodiesel with a Common-Rail HSDI Diesel Engine”, ASME 2014 12th Biennial Conference on Engineering Systems Design and Analysis, June 25-27, 2014.
17	Jumaa S. Chiad, Sadeq H. Bakhy, Ali. J. Abbed, “Study, Measuring and Vibration Data Analysis for Hip Replacement Patient during Daily Activities”, International Journal of Advanced Sport Sciences Research Vol.2 No.4, December 2014, 429-442.
18	Miqdam T. Chaichan, Khalil I. Abaas, HumamM.Salih, “Practical Investigation for Water Solar Thermal Storage System Enhancement Using Sensible and Latent Heats in Baghdad-Iraq Weathers”, June 2014.
19	Qahtan Al-Nakeeb, “Investigation Of The Accumulated Heat OfConcentrating Thermal Storage System InBaghdad/Iraqi Weather”, Journal of the Association of Arab Universities for Basic and Applied Sciences · January 2014.
20	ArkanAltaie,Moayed R. Hasan andFarhan Lafta Rashid, Numerical Heat Transfer and Turbulent Flow in a Circular TubeFitted with Opened Rings Having Square Cross Section”, Journal of Basic and AppliedScientific Research, 28-36, 2014.
21	Wahid S. Mohammad, Talib K. Murtadha, KarrarA.Ahmed, “Using TermoDeck System for Pre-Cooling/ Heating to Control the Building Inside Conditions”, Al-Khwarizmi Engineering Journal, Vol. 10, No. 3, P.P. 13- 24 (2014).
22	Dr. Mohsin NooriHamzah, Mahmood ShakirNima, “Hyperelastic Constitutive Modelling for Fiber-Reinforced Rubber Materials”, 1st International Conference on Engineering Science Applications, Kerbala, 24th-25th December 2014.
23	LaithJaaferHabeeb, Wahid Shati Mohammad , Maher abdalrazaqrashed, “Studying the Heat Transfer Characteristics in a box withHorizontal Parallel Heated Plates”, MitteilungenKlosterneuburg · October 2014.
24	Asst. Prof. Dr. Shibly Ahmed Al-Samarraie, Asst. Prof. Dr. Mohsin N. Hamzah, “Full Order Sliding Mode Control Design for VehicleABS System”, The Second Engineering Conference of Control, Computers and Mechatronics Engineering ECCCM2, 2014.
25	JafarM. Hassan,Thamer A. Mohamed,Wahid S.MohammedandWissam H. Alawee, “Modeling the Uniformity of Manifold with Various Configurations”, Journal of Fluids, Volume 2014, Article ID 325259, 8 pages, 2014.
26	Jafar M. Hassan, Thamer A. Mohamed, Wahid S. Mohammed, Wissam H. Alawee, “Experimental and Numerical Study on the Improvement of Uniformity Flow for Three-Lateral Dividing Manifold”, World Research & Innovation Convention on Engineering & Technology 2014, Putrajaya, Malaysia, 25-26 November 2014.
27	Mahmoud A. Mashkour, LaithJaaferHabeeb, HazimJassimJaber, “Natural convection in a partially Opened Box Filled Witha Porous Medium”, January 2014.
28	Jafar M. Hassan, Wahid S. Mohammed, Thamer A. Mohamed, Wissam H. Alawee, “CFD Simulation for Manifold with Taperedlongitudinal Section”, International Journal of Emerging Technology and Advanced Engineering, Volume 4, Issue 2, February 2014.
29	Raid.A. Alwan, M.A. Wahid, A.A.A. Abuelnuor and Arkan.AlTaie, “NOx Characteristics in Asymmetric Vortex Combustion”, November 2014.
30	AzherRazzaqHadiWitwit, AzmanYasin, Horizon Gitanoand Mohammed Ismael Mahmood, “Statistical Analysis for Multiple Non-linear Knock Factors in Internal Combustion Engine”, Applied Mechanics and Materials Vol. 663 (2014) pp 373-380.
31	Dr. Ibtihal Al-Namie, Dr. Mahmoud A. Mashkour, Ali Abu Al-heel Qasim, “The Effect of Ceramic Coating on Performance and Emission of Diesel Engine Operated on Diesel Fuel and Biodiesel Blends”, Journal of EngineeringNumber 6 Volume 20 June – 2014.
32	Amar Abdul-Zahra, Tillman Faßnacht, Andreas Wagner, “THERMAL STORAGE TANKS AND THE BUILDING AS STORAGE FOR LOCALLY GENERATED RENEWABLE ELECTRICITY”, June 2014.
33	Hussein J. Akeiber, Mazlan A. Wahid,Hasanen M. Hussen and Abdulrahman Th. Mohammad, “Review of Development Survey of Phase Change MaterialModels in Building Applications”, Scientific World Journal, Volume 2014, Article ID 391690, 11 pages, 2014.

Research published in the scientific journals 2015

No.	Published scientific researches for 2015	Download here
1	Wahid Shati Mohammad, "Experimental Study on Full Visualization and Startup Performance of an Oscillating Heat Pipe", Advances in Natural and Applied Sciences · January 2016.
2	Adam Dacko, Ali Jabbar Al-Khafaji, "STRENGTH AND BUCKLING ANALYSIS OF A COMPOSITE WING STRUCTURE USING MSC.PATRAN AND MSC.NASTRAN", August 2015.
3	Dheya Ghanim, "Study the Performance of a Domestic Refrigerator with Dual-Loop Cycle Flow Condenser and Comparison with Wire-on-Tube...", December 2015.
4	Hussein A Kazem, Miqdam Tariq Chaichan, "Effect of humidity on photovoltaic performance based on experimental study", December 2015.
5	Aedah Mohammed Jawad MahdY, Wahid Shati Mohammad, "Simplified Numerical Modeling of One-Dimensional Active Magnetic Regenerator.", November 2015.
6	Ali H Al-Waeli, Moanis Kamal, Hussein A Kazem, Miqdam Tariq Chaichan, "A photovoltaic application in car parking lights with recycled batteries: A techno-economic study", Australian Journal of Basic and Applied Sciences, December 2015.
7	Aedah Mohammed Jawad MahdY, Wahid Shati Mohammad, "A Novel Design of a Domestic Magnetic Refrigerator.", February 2015.
8	Dheya Ghanim, "Experimental Study of the Effect of Condenser Tubes Distribution for", November 2015.
9	Hussein A Kazem, Hilal adnan Fadhil, S. A. Aljunid, Miqdam Tariq Chaichan, "Linear and Nonlinear Modeling for Solar Energy Prediction for Zone, Region and Global Areas", December 2015.
10	Akeel Ali Wannas, "Flow Directors", October 2015.
11	Ali Jabbar Al-Khafaji, "USE LOW COST CARRIER STRATEGY AS SOLUTION TO REDUCE AIRCRAFT TICKET PRICE IN IRAQ", September 2015.
12	Miqdam Tariq Chaichan, "Control of Hydraulic Transients in the Water Piping System in Badra – Pumping Station No. 5", December 2015.
13	Miqdam Tariq Chaichan, "The impact of engine operating variables onemitted PM and Pb for an SIE fueled with variable ethanol-Iraqi gasoline...", November 2015.
14	AbdulKareem Abbas, Mohammed K. Khashan, "Improving the Lift Characteristics of Supersonic Double Wedge Airfoil at Low Speed Using Passive-Active Flow...", January 2015.
15	Hayder Abed Dhahad," Modeling and Control of Fuel Cell Using Artificial Neural Networks", January 2015.
16	Sadoon Kadhem Ayed, Mladen Aleksa Tomić, Predrag Živković," A Specific Approach for Estimating Traffic- Induced Urban Pollution", Polish Journal of Environmental Studies · September 2015.
17	Miqdam Tariq Chaichan, Improvement of NOx-PM Trade-off in CIE Though Blends of Ethanol or Methanol and EGR", December 2015.
18	Ahmed Shandookh, "Effect of Plasma Shot Peening on Mechanical Properties and Fatigue life of Al-Alloys 2024-T3", August 2015.
19	Ahmed Shandookh, "Effect of Plasma Shot Peening on Mechanical Properties and Fatigue life of Al-Alloys 7075-T6", May 2015.
20	Adel Mahmood Salih, Miqdam Tariq Chaichan, "The Effect of Variable Valve Timing on SIE Performance and Emissions", International Journal of Scientific and Engineering Research · November 2015.
21	Mladen Aleksa Tomić, Predrag Živković, Mića Vukić, Sadoon Kadhem Ayed, "The analysis of the matrix heat exchanger effectiveness", January 2015.
22	Akeel Ali Wannas, "Low-Cost Attitude and Heading Reference System Filter Using Complementary Method", December 2015.
23	Aedah Mohammed Jawad MahdY, Wahid Shati Mohammad, "Simplified Numerical Modeling of One-Dimensional Active Magnetic Regenerator.", November 2015.
24	Saša Pavlović, Darko Vasiljević, Velimir Stefanović, Zoran Stamenković, Sadoon Ayed, "OPTICAL MODEL AND NUMERICAL SIMULATION OF THE NEW OFFSET TYPE PARABOLIC CONCENTRATOR WITH TWO TYPES OF SOLAR RECEIVERS", Mechanical Engineering Vol. 13, No 2, 2015, pp. 169 - 180.
25	AbdulKareem Abbas, Modified Grid Clustering Technique to Predict Heat Transfer Coefficient in a Duct of Arbitrary Cross Section Area", June 2015.
26	Adel M Salih, Miqdam T Chaichan, Aedah M J Mahdy, "Study of the effect of elevated pressures on the laminar burning velocity of propane-air mixtures", 2015.
27	Dr. Falah F. Hatem, Humam K. Jalghef, Dr. Ahmed A. Imram, "The effect of using ramps with trench cylindrical holes on film cooling effectiveness", 2015.
28	Alaa Jaber, "Real-Time Wavelet Analysis of a Vibration Signal Based on Arduino-UNO and LabVIEW", January 2015.
29	Miqdam Tariq Chaichan, Khaleel Ibrahim Abass, "IJETT-V19P221", October 2015.
30	Hayder Abed Dhahad, "An Experimental Study on Improving The Performance of A Double Slope Solar Still Pearreview under...", January 2015.
31	Ahmed Shandookh, "Experimental Study of Plasma Shot Peening and Laser Shock Peening on Mechanical Properties and Fatigue Life of a Certain...', October 2015.
32	Hussein J. Akeiber, Seyed Ehsan Hosseini, Mazlan A. Wahid, Hasanen M. Hussen, Abdulrahman Th. Mohammad, "Phase Change Materials-Assisted Heat Flux Reduction: Experiment and Numerical Analysis", 2015.
33	Dr. Falah F. Hatem, Humam K. Jalghef, Dr. Ahmed A. Imram, "The effect of using ramps with trench cylindrical holes on film cooling effectiveness", 2015.
34	Ahmed Shandookh, "Effect of Plasma Peening on Mechanical Properties and Fatigue life of Al-Alloys 6061-T6", June 2015.
35	Adel M Salih, Miqdam T Chaichan, Abdul Al-Salam H Naser, "Study of the effect of elevated temperatures on the laminar burning velocity of propane-air mixtures", 2015.
36	Mauwafak Ali, Sadeq Hussein Bakhy, "THEORETICAL AND EXPERIMENTAL STUDY FOR CONTROLLING VIBRATION OF A PARTICULAR SYSTEM...", November 2015.
37	Kutaeba J. Al-Khishali, Adel M. Saleh, Hayder M Abbas, Miqdam T Chaichan, "EXPERIMENTAL AND THEORETICAL INVESTIGATION OF COMBUSTION OF IRAQI DIESEL FUEL", 2015.
38	Arkan K. AL-Taie, Mohammad J. Kadham, "NUMERICAL HEAT TRANSFER ENHANCEMENT IN SQUARE DUCT WITH INTERNAL RIB", Eastern Academic Journal, Issue 3, pp.87-100, October, 2015.
39	Ihsan A.Baqer, Somer Nacy, "Modeling of 3D Grasping of Artificial Hand Under Dynamic Load", January 2015.
40	Adel Sharif Hamadi, Hayder Abed Dhahad, "An Experimental Investigates to Study the Effect of Zinc Oxide Nanoparticles Fuel Additives on the...", January 2015.
41	Wahid Shati Mohammad, "A Novel Design of a Domestic Magnetic RefrigeratorPractical Study of Magnetic Refrigeration Performance and...", International Journal of Innovation Science · February 2015.
42	Aedah M. Jawad Mahdy, Wahid S. Mohammad, Talib K. Murtadha, "Simplified Numerical Modeling of One-Dimensional Active Magnetic Regenerator", Volume 5(7):PP. 237-253, 2015.
43	Aedah M. Jawad Mahdy, Wahid S. Mohammad, Talib K.Mortada, "Practical Study of Magnetic Refrigeration Performance and Optimization", IOSR Journal of Mechanical and Civil Engineering (IOSR-JMCE), e-ISSN: 2278-1684,p-ISSN: 2320-334X, Volume 12, Issue 2 Ver. II, March 2015.
44	Hayder Abed Dhahad, "A Cognitive Neural Linearization Model Design for Temperature Measurement System based on Optimization Algorithm", May 2015.
45	Ass. Prof. Dr. Emad Natiq Abdulwahab, Ass. Prof. Dr. Mohammed Idrees Mohsin, "STATIC CALIBRATION OF TRIAXIAL ACCELEROMETER USING NONLINEAR NUMERICAL METHOD", Journal of Engineering and Development, Vol.19, No.4. July. 2015.
46	Samir Ali Amin Al-Rubaie, Qasim Abbas Atiah, Zuhair Altaher, "Determination of Optimum Welding Parameters for FSW AA2024-T351", Al-Khwarizmi Engineering Journal, Vol. 11, No. 1, P.P.51-64, 2015.
47	Shaker S.Hasan, Somer M. Nacy, Enass H. Flaieh, "Optimization and Analysis of Underactuated Linkage Robotic Finger", Innovative Systems Design and Engineering, Vol.6, No.6, 2015.