Hayder Abed Dhahad
Prof. Dr. Hayder Abed Dhahad
Faculty Member of Mechanical Engineering Dept.
Vice president of Scientific Affairs and Higher Education Studies - University of Technology- Iraq
عنوان البريد الإلكتروني هذا محمي من روبوتات السبام. يجب عليك تفعيل الجافاسكربت لرؤيته.
"Professor Dhahad received his Ph.D. (2014) in Mechanical Engineering from University of Technology- Iraq. He graduated from University of Technology - Iraq in 1994 and 1998 for his bachelor and master degrees. Currently, he is a faculty member in the Department of Mechanical Engineering, University of Technology- Iraq. Also, he has a position of a vice president of scientific affairs and higher education studies - University of Technology- Iraq. He authored and co-authored nearly 50 papers published in high ranking prestigious international journals and conferences. Recently, he is a guest editor for energies journal for special issue "Hydrogen - New Alternative Fuel". His research fields focus on renewable energy, biofuels, IC engines, combustion, solar Energy, fuel cells.
PhD, Mechanical Engineering, University of Technology- Iraq,2014.
MSc, Mechanical Engineering, University of Technology- Iraq, 1998.
BSc, Mechanical Engineering, University of Technology- Iraq, 1994.
Renewable Energy, Combustion, Solar Energy, Fuel Cell, Thermofluid
1. "Proposal and thermo-economic optimization of using LNG cold exergy for compressor inlet cooling in an integrated biomass fueled triple combined power cycle " International Journal of Hydrogen Energy "2021-
2. "A novel hybrid biomass-solar driven triple combined power cycle integrated with hydrogen production: Multi-objective optimization based on power cost and CO2 emission " Energy Conversion and Management, 234,2021.
3. "Study effects of bio-inspired flow filed design on Polymer Electrolyte Membrane fuel cell performance" Case Studies in Thermal Engineering, 24,2021
4. "Thermo-economic evaluation of a combined Kalina cycle and humidification-dehumidification (HDH) desalination system integrated with thermoelectric generator and solar pond" International Journal of Heat and Mass Transfer, 168,2021
5. "Heat recovery application of nanomaterial with existence of turbulator" Journal of Molecular Liquids, 326,2021
6. "Energy, exergy, and exergoeconomic evaluation of a novel CCP system based on a solid oxide fuel cell integrated with absorption and ejector refrigeration cycles" Thermal Science and Engineering Progress, 21,2021
7. "Improving the performance of pyramid solar still using rotating four cylinders and three electric heaters" Process Safety and Environmental Protection, 148,2021
8. "Nanomaterial transportation and exergy loss modeling incorporating CVFEM" Journal of Molecular Liquids,330,2021
9. "Effects of adding aluminum oxide nanoparticles to butanol-diesel blends on performance, particulate matter, and emission characteristics of diesel engine" Fuel,286,2021
10. "on-DarcianBénard convection in eccentric annuli containing spherical particles" International Journal of Heat and Fluid Flow, 86,2020.
11. “The Cooling Performance of Mixed Convection in a Ventilated Enclosure with Different Ports Configurations" Journal of Heat Transfer, 142,12,2020.
12. "Thermo-economic investigation and multi-objective optimization of a novel enhanced heat pump system with zeotropic mixture using NSGA-II" Applied Thermal Engineering, 2020.
13. "Variation of Coefficient of Friction and Friction Head Losses Along a Pipe with Multiple Outlets" Water,2020,12,844.
14. "Role of different antioxidants additions to renewable fuels on NOX emissions reduction and smoke number in direct injection diesel engine" Fuel,2020,279,118384.
15. "Aiding and Opposing Re-circulating Mixed Convection Flows in a Square Vented Enclosure" Thermal Science and Engineering Progress, 19 (2020) 100577.
16. "Combustion analysis and performance characteristics of compression ignition engines with diesel fuel supplemented with nano-TiO2 and nano-Al2O3) Case Studies in Thermal Engineering, 20 (2020) 100651
17. "Influence of thermal buoyancy on vortex shedding behind a circular cylinder in parallel flow" International Journal of Thermal Sciences, 156 (2020) 106434
18. "The impact of adding nano-Al2O3 and nano-ZnO to Iraqi diesel fuel in terms of compression ignition engines' performance and emitted pollutants" Thermal Science and Engineering Progress, 18 (2020) 100535
19. "Thermodynamic and thermoeconomic analysis of innovative integration of Kalina and absorption refrigeration cycles for simultaneously cooling and power generation" Energy Conversion and Management, 203 (2020) 112241.
20. "Performance, regulated and unregulated exhaust emission of a stationary compression ignition engine fueled by water-ULSD emulsion" Energy, 181 (2019) 1036-1050.
21. "Experimental Study Of The Effect Of Flow Field Design To PEM Fuel Cells Performance" Renewable Energy Focus Volume 30, Number 00 September 2019.
22. "A Neural Networks Based Predictive Voltage-Tracking Controller Design For Proton Exchange Membrane Fuel Cell Model) Journal Of Engineering. Number 12 Volume 25 December 2019.
23. "Experimental Study On The Effect Of Nanoparticle Addition On The Pressure At The Start Of Ignition, Maximum Pressure And Timing Of Maximum Pressure) Arpn Journal Of Engineering And Applied Sciences. Vol. 14, No. 8, April 2019
24. "Increase The Yield Of Simple Solar Distillation Using The Water Drip Method" International Journal Of Computation And Applied Sciences IJOCAAS, Volume 6, Issue 2, April 2019
25. "Variation Of Flow Along A Multiple Outlets Pipe With Various Spacing And Inflow Water Head Based On Physical Model) Journal Of Engineering Science & Technology. Volume14, Issue 5- 2019
26. "An Experimental Investigation Of Impact Of Zro2 Nanoparticles In DI Engine Performance". Kirkuk University Journal /Scientific Studies (KUJSS) 3-2019
27. "Effect Of Flow Field Design And Channel/Header Ratio On Velocity Distribution: An Experimental Approach" Thermal Science And Engineering Progress 8 (2018) 118–129
28. "Study The Effect Of Different Percentages Of Natural (Orange Peels And Date Seeds) And Industrial Materials (Carbon And Silica) On The Mechanical And Thermal Properties Of Polymeric Reinforced Composites". Al-Khwarizmi Engineering Journal, Vol. 14, No. 4, December, (2018)
29. "An Experimental Investigation Of Combustion Emissions And Diesel Engine Performance Of Water In Diesel Nano Emulsion Fuel". 4th Iraq Oil & Gas Conference. 13-14 Dec. 2017, Basra, Iraq.
30. "AN EXPERIMENTAL INVESTIGATES TO STUDY THE EFFECT OF ALUMINUM OXIDE NANOPARTICLES FUEL ADDITIVES ON THE PERFORMANCE AND EMISSIONS CHARACTERISTICS OF DIESEL ENGINE" The 1st International Scientific Conference Of Nanotechnology And Advanced Materials In The Petroleum And Gas Industry. University Of Technology-Baghdad-Iraq, 3-4 May 2017.
31. "Digital Flow Rate Measurement System Design ForMinichannel Based On Cross Correlation Technique". Eng. And Technology Journal- University Of Technology Vol. 35, Part A, No. 7, 2017.
32. "Effect Of Aluminum Oxide Nanoparticles Fuel Additives On The Performance And Emissions Of Diesel Engine" Engineering And Technology Journal. Vol. 35, Part A, No. 9, 2017
33. "Effect Of Geometric Design Of The Flow Fields Plat On The Performance Of A PEM Fuel Cell. A Review" World Research & Innovation Convention On Engineering & Technology 2016, Langkawi, Kedah, Malaysia, 24-25 October 2016
34. "Experimental Study Of The Operating Temperature Effect On The Performance Of PEM Fuel Cell" World Research & Innovation Convention On Engineering & Technology 2016, Langkawi, Kedah, Malaysia, 24-25 October 2016
35. "Modeling And Control Of Fuel Cell Using Artificial Neural Networks" Journal Of Engineering, Baghdad University, Number 12 Volume 21 December – 2015.
36."An Experimental Investigates To Study The Effect Of Zinc Oxide Nanoparticles Fuel Additives On The Performance And Emissions Characteristics Of Diesel Engine" The Iraqi Journal For Mechanical And Material Engineering, Special Volume -Babylon First International Engineering Conference Issue (B) 2016
37. "An Experimental Study On Improving The Performance Of A Double Slope Solar Still". The 7th International Conference On Sustainable Agriculture For Food, Energy And Industry In Regional And Global Context, ICSAFEI2015”. Universiti Putra Malaysia From 25-27 August 2015.
38. "Cognitive Neural Linearization Model Design For Temperature Measurement System Based On Optimization Algorithm". The Engineering And IJCCCE Journal, University Of Technology – 2015
39. "The Influence Of Injection Timing On Combustion And Emission Characteristics Of HSDI Diesel Engine". Eng. And Technology Journal- University Of Technology, Vol.32, Part (A), No.9, 2014.
40. "The Influence Of Injection Pressure On Combustion And Emission Characteristics Of A Common-Rail HSDI Diesel Engine". Thi-Qar University Journal For Engineering Sciences, Vol. 4, No.4 , 2013.
41. "An Investigation Of The Relation Between Premixed Burn Fraction And Emissions Characteristics Of A Common-Rail HSDI Diesel At Different Loads". International Conference For Engineering Sciences- Al-Mustansirya University, 2014.
42. "Experimental Combustion Characteristics, Nanoparticles And Soot-Nox Trade Off In A Common-Rail HSDI Diesel Engine Running On ULSD And HFO Fuels". World Research & Innovation Convention On Engineering & Technology 2014, Putrajaya, Malaysia, 25-26 November 2014
43. "The Relation Of Combustion Phases And Emissions Of ULSD & HFO In A Common-Rail HSDI Diesel Engine". International Journal Of Scientific & Engineering Research. Volume 5, Issue7, July 2014.
44. "An Investigation of The Relation Between Combustion Phase And Emissions Of ULSD & RME Biodiesel With A Common-Rail HSDI Diesel Engine" ASME 2014 12th Biennial Conference On Engineering Systems Design And Analysis-ESDA2014- June 25-27, 2014, Copenhagen, Denmark.
45. "Effects of Injection Pressure On Combustion, Nanoparticles And Gaseous Emissions Characteristics From A Common-Rail HSDI Diesel Engine Running On ULSD And RME" Proceedings Of The ASME 2014 Internal Combustion Engine Division Fall Technical Conference-ICEF2014- October 19-22, 2014, Columbus, IN, USA.
46. "Temperature Profile Measurement in Non-Premixed Turbulent Flame Near Lean Limit Of LPG/Air Mixture" Eng.& Tech. Journal, Vol.28, No.8, 2010
47. "Charge Stratification and Fuel/Air Ratio Effect On The Efficiency Of (ICADE) I. C. Engine Cycle" Al-Khwarizmi Engineering Journal, Vol. 7, No. 3, PP 68 - 77 (2011)
48. "The Effect of Isolated Air Mass And Fuel/Air Ratio On The Efficiency Of IASME INTERNATIONAL MECHANICALENGINEERING CONGRESS AND EXPOSITION, Octobar 31- November 6,2008 Boston Massachusetts.
49. "Measurement Of Temperature Profile In Non-Premixed Turbulent Flame Of LPG/Air Mixture" ASME Power,2008, Orlando,FL, USA On 07/22/2008 – 07/ 24 /2008.
For MSc Level:
Advanced measurements
For BSc Level:
Level 4: Measurements
Level 4: Internal combustion engines design
Many certificates of appreciation from the Minister of Higher Education and the President of the University of Technology.
Ali Hussein Alwan
Lecturer: Ali Hussein Alwan
Faculty Member of Mechanical Engineering Dept.
General Mechanical Branch Coordinator.
عنوان البريد الإلكتروني هذا محمي من روبوتات السبام. يجب عليك تفعيل الجافاسكربت لرؤيته.
I have finished my B.Sc. degree in Mechanical Engineering – University of Technology – Baghdad- Iraq -2006 and M.Sc. degree in Mechanical Engineering- applied mechanics for the University of Technology in 2015. Currently I am a member in mechanical engineering department teaching staff at University of Technology, Baghdad - Iraq.
2006 - B.Sc. in Mechanical Engineering from University of Technology – Baghdad-Iraq
"Stress Analysis, Stress Measurements, Machine Design, mechanical properties of materials. Iraq "
8-Najmuldeen Yousif Mahmood and Ali Hussein Alwan,’’Mechanical properties improvement of MIG welding steel sheets using Taguchi method”,Taylor and Francis, Australian Journal of Mechanical Engineering,2019.
9-A.H. Alwan, N.Y. Mahmood, Parameters optimization of MAG welding for enhancing the mechanical properties and buckling behaviour of welded steel, Journal of Achievements in Materials and Manufacturing Engineering, 2020.
"A- Dynamic (for second class)
-Machine Design I (for third class) tutorial class.
-Automotive Design (for fourth class) tutorial class.
"- 20 thank and appreciation letters form the Dean of mechanical engineering department.
- 8 thank and appreciation letters form the president of university of technology.
- IC3 test certificate from Certiport Company.
Mahmoud A. Mashkour
Mahmoud A. Mashkour
Mechanical Engineering Department
Assistant Professor
عنوان البريد الإلكتروني هذا محمي من روبوتات السبام. يجب عليك تفعيل الجافاسكربت لرؤيته.
"Asst. Prof. Dr. Mahmoud A. Mashkour
Mechanical Engineering Department
Assistant Professor since 2012.
Baghdad – Iraq. +096-7901514059
عنوان البريد الإلكتروني هذا محمي من روبوتات السبام. يجب عليك تفعيل الجافاسكربت لرؤيته.
عنوان البريد الإلكتروني هذا محمي من روبوتات السبام. يجب عليك تفعيل الجافاسكربت لرؤيته.
"2004-2005 PhD in Mechanical Eng. / Heat Engines / Internal Combustion Engines
1994-1995 MSc in Mechanical Eng. / Power Generation
1989-1990 BSc in Mechanical Engineering"
"- Internal combustion engines-Thermodynamics; Control and Design.
- Fuel and combustion.
- Heat transfer.
- Modeling and Numerical analysis.
- Nano technology.
"
1-Dr. Mahmoud A. Mashkour, Mustafa Hadi Ibraheem"3D-CFD Heat Transfer Simulation within Spark Ignition Engine",journal of kerbala university, Vol. 17, No. 2, pp.64-88, 2019.
2-Dr. Mahmoud A. Mashkour, Mustafa Hadi Ibraheem"CFD Analysis of Petrol Internal Combustion Engine", Journal of University of Babylon for Engineering Sciences, Vol. 26, No. 9, pp.132-148, 2018.
3-Dr. Mahmoud A. Mashkour, Ahmed Yaseen Ahmed "Investigation of Spark Ignition Engine Mathematical Model Using MATLAB (GUI)", ADVANCES in NATURAL and APPLIED SCIENCES, September 11(11):pages 36-50, 2017.
4-Dr. Mahmoud A. Mashkour, "Effect of Diesel Fuel Sources on Engine Emissions" – Association of Arab Universities Journal, Vol. 18, No. 2, -2011.
5-Dr. Ibtihal Al-Namie, Dr. Mahmoud A. Mashkour, Ali Abu Al-heel Qasim, "The effect of ceramic coating on performance and emission of diesel engine operated on diesel fuel and biodiesel blends" - Journal of Engineering University of Baghdad-2014.
6-Dr. Kutaiba JM AL-Khishali, Dr. Mahmoud A. Mashkour, Ehsan Shamil Omaraa, "Analysis of Flow Characteristics in Inlet and Exhaust Manifolds of Experimental Gasoline Combustion in a VCR Engine" - Eng. & Tech. Journal, Vol.28, No.7, 2010.
7-Dr. Mohammedali Abdulhadi, Dr. Mahmoud A. Mashkour, "Two zone model simulating the combustion process of dual fuel in S.I.E." - Scientific Conference of Energy and Renewable Energy Applications, pp.300-316-2011.
8-Dr. Abed Al-Khadim M. Hasan, Dr. Mahmoud A. Mashkour & Amer A. Mohammed "Experimental study of kerosene additive to waste oil biodiesel for using as alternative diesel fuel", International Journal of Engineering Research and Modern Education, Volume I, Issue II, 2017.
9-Dr.Arkan Khikhal Husain, Dr.Mahmoud Attallah Mashkour, Fuad Abdul Ameer Khalaf "Numerical Investigation of Influence of Multi-Line Fuel Injection (Methane) on a Tubular Combustor Emissions of Micro Gas Turbine", Journal of University of Babylon for Engineering Sciences, Vol.26, No.7, pp.271-285, 2018.
10- Dr. Mahmoud A. Mashkour, Dr. Laith Jaafer Habeeb, Hazim Jassim Jaber "Heat Transfer in a partially Opened Cavity Filled with Porous Media", 3rd Scientific International Conference 2013 / Najaf, pp. 601-614.
"Undergraduate courses:
1. Internal Combustion Engines, Department of mechanical Engineering, University of Technology- 3rd year.
2. Design of Internal Combustion Engines, Department of mechanical Engineering, University of Technology- 4th year.
3. Thermodynamic principles, Department of mechanical Engineering, University of Technology. 1st year.
4. Numerical Analysis, Department of mechanical Engineering, University of Technology- 3rd year.
5. Mechanical Drawing, Department of mechanical Engineering, University of Technology- 2nd year.
6. Mathematics, Department of mechanical Engineering, University of Technology- 1st year.
7. Advanced Mathematics, Electrical Engineering Department, University of Technology- 3rd year.
8. Perspective Engineering, Department of mechanical Engineering, University of Technology- 1st year.
Postgraduate courses:
• Msc courses:
1. Advanced Thermodynamics, M.Sc. Course in Thermal Power, Department of mechanical Engineering, University of Technology.
2. Supervised number of Ph.D. and M.Sc. thesis.
"
"- Greater than 42 -Acknowledgment from the Minister of Higher Education of Iraq (2), the President of University of Technology (18) and Dean of Mechanical Engineering Department (22) for scientific efforts.
- University Shield – 2012.
- Certificates of appreciation.
"
Ekhlas Mohammed Fayyadh
Ekhlas Mohammed Fayyadh
Mechanical Engineering Department
Assistant Professor
عنوان البريد الإلكتروني هذا محمي من روبوتات السبام. يجب عليك تفعيل الجافاسكربت لرؤيته.
I earned bachelor science in mechanical engineering , Master of power generation ,and Doctor of Thermal power .
"B.Sc. Mechanical Engineering.1981,M.Sc. Power Generation. 1987,Ph.D Thermal power1997 "
Fluid Mechanic,Heat Transfer, Wind Turbine,Flow Boiling, fluidization
1- The effect of diameter ratio on local heat transfer coefficient for vertical
cylinders , J. of Eng.&Tech. , 1988.
2- The effect of flow velocity on local heat transfer coefficient . Pub. In J. of Eng.&Tech. , Vol.11, No.8, 1992.
3- The influence of various factors on the fuel consumption of petrol powered vehicles using a computer simulation method Pub. In Energy ,Vol.18, No.1, pp63-68, 1993.
4- New development in the wind evaluation of wind energy potential in Iraq, The second scientific conference of Babylon University , 23-25 April ,1996.
5- Aerodynamic optimization of low speed wind turbine rotor, the second scientific conference of college of Eng., University of Tikrit, 1-2 Oct.1996.
6- Thesis submitted for the degree of doctor "Comprehensive Evaluation and Aerodynamic Study of Wind Energy Conversion Systems for Iraq". Of philosophy department of mechanical engineering University of -Technology, Baghdad-Iraq.1996.
7- "Performance of vertical axis wind turbine and inability of starting "Accepted in journal of Tech.12/11/2000.
8- "Parameters affecting the aerodynamic of the wind turbine rotor design "
3rd.Eng. Scientific Conference Organized by Military College of Engineering,23-25 April 2000.
9- "Effect of airfoil geometry on the laminar separation characteristics "Pub. In Journal of Babylon University, Vol.6, No.5, 2000.
10- "Tip clearance effect of the finite wing haracteristics "Pub. In J. of Eng. &Tech., Vol.20, No.5 , 2001.
11- "Prediction of three dimensional natural convection from heated disks and rings at constant temperature ",Pub. In J. of Eng. &Tech., Vol.22 , No.5 , 2003.
12- " Measurement of three dimensional natural convection heat transfer from disc and rings facing upward and downward at constant temperature ".Pub. In J. of Eng. &Tech., Vol.22 ,No.5 ,2003.
13- "Natural convection heat transfer from horizontal discs and rings facing
up at constant heat flux ".Pub. In J. of Eng. &Tech., Vol. 23,No.6 , 2004.
14- " Natural convection from single finned tube immersed in a tilted
enclosure" Pub. in J. of Eng. No.3 Vol.13 .2006.
15- "Numerical study for a three dimensional laminar natural convection
Heat transfer from an isothermal heated horizontal and inclined square Plate and with a circular hole" Pub.in J. of Eng. No.2 Vol.13 .2007
16- " Effect of internal acoustic excitation on improvement of airfoil
performance" Pub.in Al-Khwarizmi Engineering Journal No. Vol.32007
17- "Numerical and experimental investigation on the effect of restriction
Shape on characteristics of airflow in a square duct”, Pub. in J. Eng. of Baghdad Number 4 Volume 16 December 2010.
18- "Experimental study for a three dimensional laminar natural convection
Heat transfer from an isothermal heated square plate "Pub. accepted in J. Eng. of Baghdad 2008.
19- "Experimental study on the presence of open cavity effects on internal
Flow and convection heat transfer characteristics” Pub. in J. Eng. of Baghdad Number 3 Volume 16 September 2010
20- "Experimental study for a three dimensional laminar natural convection
Heat transfer from an isothermal heated square plate with and without Circular hole "Pub. In J. Eng. of Baghdad Number 2 Volume 18 February 2012
21- ”Experimentally drag reduction for airfoil sections by riblets techniques” Pub. in University of Baghdad, Engineering Journal, No.992,. 2008.
22- ”Thermal characterization for a thin enclosure with an immersed perforated finned tube bundle” Pub. In secientific refereed Journal
published by gulf university Kingdom of Bahrain vol.3 No.1 Engineering and Computer Engineering Division 2011
23- " Effect of Riblets Geometry on Drag Reduction"; ASME 2012 International Mechanical Engineering Congress and Exposition Volume 7: Fluids and Heat Transfer, Parts A, B, C, and Houston, Texas, USA, November 9–15, 2012
24- "The Influence of Injection Timing on Combustion and Emission
Characteristics of HSDI Diesel Engine " Eng. & Tech. Journal ,Vol.32,
Part (A), No.9, 2014
25- "The Relation of Combustion Phases and Emissions of ULSD & HFO in a Common-Rail HSDI Diesel Engine" International Journal of Scientific & Engineering Research, Volume 5, Issue 7, July-2014
26- "An Investigation of the Relation Between Combustion Phase and Emissions of ULSD & RME Biodiesel With a Common-Rail HSDI Diesel Engine" ASME 2014 12th Biennial Conference on Engineering
Systems Design and Analysis, Copenhagen, Denmark, July 25–27, 2014; 06/2014
27- . "A New Multi-Objective Evolutionary Algorithm for Optimizing the Aerodynamic Design of HAWT Rotor", ASME 2014 12th Biennial Conference on Engineering Systems Design and Analysis, Copenhagen, Denmark, July 25–27, 2014; 06/2014
28- ."Flow Boiling Heat Transfer of R134a in Multi Micro Channels", Proceedings of the World Congress on Mechanical, Chemical, and Material Engineering (MCM 2015) Barcelona, Spain – July 20 - 21,
2015 Paper No. 296
29- ."Single Phase Flow Pressure Drop and Heat Transfer in Rectangular Metallic Micro channels", Applied Thermal Engineering 93 (2016) 1324–1336
30- " Effect Of Geometric Design Of The Flow Fields Plat On The Performance Of A PEM Fuel Cell. A Review Conference: World Research & Innovation Convention on Engineering & Technology 2016, Langkawi, Kedah, Malaysia, 24-25 October 2016
31- ." The Combined Effect of Rib with Single Large Eddy Break Up Devices on Flow and Heat Transfer Characteristic of Turbulent Flow in
Rectangular Duct", Al-Nahrain Journal for Engineering Sciences (NJES) Vol.20 No.1, 2017 pp.281 – 291
Fluid Mechanic ,Application of Fluid ,Two phase flow
Appreciation Certificate from Minister of higher education
Ali Dawood Salman Ali
Ali Dawood Salman Ali
Mechanical Engineering Department
Lecturer
عنوان البريد الإلكتروني هذا محمي من روبوتات السبام. يجب عليك تفعيل الجافاسكربت لرؤيته.
"The Certification
-I got my B.Sc. degree in Refrigeration and air conditioning division, from Mech. Eng. Dep. , University of Technology, Baghdad, Iraq.(1998-1999).
-Then I got the M.Sc. degree in Refrigeration and air conditioning, Mech. Eng. Dep. UOT, Baghdad, Iraq, in 2002. Thesis title"" Simulation of Design of Roll Bond Evaporator Working with Alternatives Refrigerants of R-12""
- I finished my study, and earned the Ph.D. degree in Mechanical engineering department, university of Technology, Baghdad, Iraq. where the title of thesis "" COMBINED HEAT PIPE AND PCM FOR HEATING AND VENTILATION"", 2017.
experience
me experience present my division RAC, where I was started to work in the local markets in Iraq, as RAC engineer, by instilling designing and repairing the RAC equipment, also I worked in air duct design and cooling, heating estimation load, for long years.
The Job.
I employed in the Electromechanical Eng. Dep. UOT, Baghdad, Iraq. 2006, where I was started my Job as a member of teaching staff. then, in 2017 I become a staff member in the mechanical engineering Dep. RAC division UOT, Baghdad. Iraq,
"
"1999- B.SC. degree in Refrigeration and air conditioning Eng. division/ Mech. Eng. Dep./University of Technology, Baghdad, Iraq.
2002- M.Sc. degree in Refrigeration and air conditioning Eng. division/, Mech. Eng. Dep. UOT, Baghdad, Iraq, in 2002.
thesis tile "" Simulation of Design of Roll Bond Evaporator Working with Alternatives Refrigerants of R-12""
2017- Ph.D. degree in Mechanical engineering department, university of Technology, Baghdad, Iraq. the title of thesis "" COMBINED HEAT PIPE AND PCM FOR HEATING AND VENTILATION"", 2017.
"
"Heat dissipation from the CPU, GPU and mini heat exchanger. Heat and mass transfer through frost formation and melting. Air conditioning for building and renewable energy. "
1-"Transient Behavior Analysis for Solar Energy Storage in PCM-CFM Material Using Equivalent Heat Capacity Method as Storage Model
Al-Khwarizmi Engineering Journal
2018 | journal-article
"
2-"Experimental and Numerical Study of Closed Loop Solar Chimney Assisted with PCM and CFM as Thermal Energy Storage Collector
Eng. & Tech. Journal
2016 | journal-article"
3-"Experimental Study Using the Passive Solar Chimney for Evaporative Cooling with PCM and CFM as a Thermal Energy Storage
Al-Khwarizmi Engineering Journal
2016 | journal-article"
4-"Heat Rejection from Horizontal Tube through Heat Valve
Eng. & Tech. Journal
2012 | journal-article"
5-"A Study for the Influence of Change in Ratio of Cross Sectional Area to Constant Perimeter of Thermosyphon's Condenser
Eng. & Tech. Journal
2011 | journal-article"
6-"Simulation of Design of Roll Bond Evaporator Working with Alternatives Refrigerants of R-12
Eng. & Tech. Journal
2005 | journal-article"
7-Thermal Efficiency for Passive Solar Chimney With and Without Heat Storage material
"- Computer Add Drawing 1st year, power and renewable energy Eng. division, Electromechanical Eng. Dep./University of Technology, 2006-2012
- Simulation 3rd year, power and renewable energy Eng. division, Electromechanical Eng. Dep./University of Technology, 2009-2011
- CAD CAM 4th year, mech. Eng. division Electromechanical Eng. Dep./University of Technology, 2008-2009
- Instrumentation 2nd year, RAC division mech. Eng. Dep., /University of Technology, 2017 until now
- Air Conditioning II 3rd year, RAC Division, Mech. Eng.. Dep., ,/ University of Technology, 2018 until now
-Computer Add Drawing 2nd year, power plant division, Mech. Eng. Dep.,/ University of Technology, 2017 until now.
-RAC Lab. 4th year power and renewable energy Eng. division, Electromechanical Eng. Dep., / University of Technology, 2006-2016
-Air Conditioning Lab. 3rd year, RAC division, Mechanical Eng. Dep./ University of Technology, 2018-2019.
-Refrigeration Lab. 3rd year, RAC division, Mechanical Eng. Dep./ University of Technology, 2017-2018."
"- Certificate of Excellence from GSCS company to me as HVAC engineer. 2015
- IC3 certification. 2011
-Certificate English language, College of Education for women, University of Baghdad. 1999
- English certification (TOFEL) 2011.
-certificate for Computing and Computer Software, Computer Center, University of Technology, 2008.
-
-Four thank and appreciation letters from the president of the University of Technology.
- More than 12 thank and appreciation letters from the Dean of the Electromechanical Eng. Dep.
- More than 4 thank and appreciation letters from the Dean of the Mechanical Eng. Dep.
"
